Skip to content
Harvest savings this November 🍂 Save 10%. "harvest" at checkout. Rise plants 3 trees 🌳 with every order to help reforest the planet.
Harvest savings this November 🍂 Save 10%. "harvest" at checkout. Rise plants 3 trees 🌳 with every order to help reforest the planet.

AFM Safecoat 3 in 1 Adhesive

2 reviews
SKU 71210
Original price $34.00 - Original price $85.00
Original price
$34.00
$34.00 - $85.00
Current price $34.00
Fall into savings 🍂. Save 10% on select products with harvest at Checkout. Brand and product exclusions apply

Why Is This Product On Rise?

AFM Safecoat® 3 in 1 Adhesive is a low-odor, formaldehyde-free, and water-based mastic adhesive that is designed for hard composition wall and floor tiles and carpeting. 

Specifically, Safecoat 3 in 1 Adhesive is recommended for adhering floor tiles made of ceramic, vinyl, parquet, and slate; for lightweight wall tiles; and for any carpet application where a typical carpet adhesive would be used.

What's Included

  • Available in quart or gallon sizes

Specifications and Important Details

Clean-up

Clean tools and equipment while they are still wet with a warm soapy water solution. 

 

Drying/Curing time

24hrs for a full cure.

 

Health Precautions

As with all adhesives, keep container tightly closed and out of the reach of children. Do not take internally. Keep from freezing. Always use adequate ventilation. If you are chemically sensitive, always test for personal tolerance.

Installation Notes

Prep

Surface must be level before application, as use of Safecoat 3 in 1 Adhesive will not substitute for a leveling compound, especially over surfaces such as concrete. All substrates to receive adhesive and overlays must be sound and intact. Any loose areas should be repaired or anchored to produce a firm footing for adhesion. All surfaces must be cleaned of any grease, oils, dust, dirt, wax, unsound prior adhesive and other foreign materials. Washing with a low odor, not toxic cleaner like SafeChoice Cleaner is recommended. Best results can be obtained if non-porous surfaces are dry and stable prior to application. Porous surfaces will benefit from a coat of Safecoat Safe Seal prior to application of 3 in 1 Adhesive (for maximum adhesion, even non-porous surfaces benefit from the application of a thin coat of Safecoat Safe Seal to the substrate and if possible the surface to be adhered – for example the back of the tile - before spreading adhesive and laying the tiles). 3 in 1 can be applied over slightly tacky SafeSeal. Use adequate ventilation. Refer to flooring manufacturer’s specific recommendations. Adjust the temperature of the area to be installed, adhesive, and flooring to at least 65°F (18°C) or above for 48 hours before, during, and 48 hours after installation.

 

Application

Always have adequate ventilation. Stir any liquid on the surface into the adhesive. For carpeting, cementitious and ceramic tile, application should be made with 1/8” or larger notched trowel (commonly v- notched for walls and square notched for floors, but consult your installer). A 3/16” notched trowel should be used for wall tiles. All other applications require 1/16”, including residential felt-back rotovinyl sheet flooring. Due to rapid cure do not spread the adhesive over areas larger than 16-20 square feet.Allow adhesive to set up or “tack-up” for a few minutes (typically not more than 10-15 depending upon temperature and humidity), and then insert tiles into mastic. Maintain a wet, tacky surface during installation of the tile. Do not allow adhesive to skim over. If a film forms or adhesive skims over, or sets up so that it is no longer sticky, scrape all adhesive off the surface and reapply. Allow 24 hours for 3 in 1 Adhesive to cure out before opening to traffic or for any further surface filling. A trial application is recommended to assure proper adhesion can be obtained. Testing is particularly important for parquet and wooden floor material, which varies considerably in consistency and may have a tendency to warp. Again, seal the bottom of the material with Safecoat Safe Seal to help provide a moisture barrier. Roll flooring in both directions with a 75–100 lb. roller and seal seams as recommended by the flooring manufacturer. Stiff carpets/sheet goods should be rolled again after 2 hours. Restrict heavy traffic for 24-48 hours. Protect adhesive (specifically carpet installations) from exposure to water from cleaning and other sources for a minimum of 30 days after installation

 

 

Documentation and Tear Sheets

Customer Reviews
5.0 Based on 2 Reviews
5 ★
100% 
2
4 ★
0% 
0
3 ★
0% 
0
2 ★
0% 
0
1 ★
0% 
0
100reviewers would recommend this product Write a Review Ask a Question

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

Filter Reviews:
RL
09/05/2022
Rich L.
United States
I recommend this product

Perfect in the Kitchen

The non-toxic water-based SafeCoat 3-in-1 adhesive is just as good, if not better than the stinky mortar used to put up tile. I’ve been using this in the kitchen for a subway tile backsplash from countertop to ceiling (no upper cabinets). I’m 100% satisfied and highly recommend this product!

A
04/05/2022
Anonymous
United States United States
I recommend this product

It works!

I installed standard subway tile using this glue and it worked great! It dries a little slower than type 1 adhesive which is a plus. Everything was set in 24 hrs. A little goes a long way too.

Interested in Deals and New Products?

Keep up-to-date on deals and new home building products that benefit your health, your wealth, and the planet delivered right to your inbox.